Tools/Maintenance

• Essential mechanic tool to properly service and maintain all RockShox products • For RockShox Monarch

Rear Shock Air Valve Adapter (for charging IFP) - SIDLuxe A1+ (2020+)

This is RockShox's recommended cleaner for suspension internals. Handy aerosol spray degreases and conditions small parts like O-rings and seals. - Formulated with special conditioners that will not cause O-rings and seals to dry, crack, or degrade - For use on all suspension products

Low viscosity mineral oil for use with Campagnolo hydraulic brake systems. - Does not absorb water so regular bleeding is not necessary - Non-toxic and will not irritate skin - Will not damage frame finishes

Everyone wears out their Park Tool work stand clamp covers at some point. Find replacement covers for yours here. Each cover is constructed of soft, durable composite rubber. See below to determine which covers fit your Park Tool stand clamp: - 1002: fits 100-3X and 100-5X extreme range clamps - 1185: fits clamps on the repair stands PCS-9, PCS-10, PCS-11, and PCS-12 - 1259: fits 100-4X, 100-6X, 100-7X, and 100-15X clamps - 1960: fits 100-3D, 100-5D, and 100-25D Professional Micro Adjust Repair Stand Clamps - 468B: fits clamps with double cable reliefs, including 100-3C, 100-5C, 100-8C, 100-8Y, and 100-9C clamps - 467B: fits clamps with single cable relief, including PRS-2 through PRS-8 (for older-style clamps, non-current) - 468G: fits PCS-1 and PCS-2 clamps with double cable reliefs (clamp models: 100-1C, 100-1CA, and 100-2C) - 467G: fits PCS-1 and PCS-2 clamps with single cable relief (for older PCS-series stands only; not for current model stands) - 466: Rubber Replacement Clamp Cover Set (fits older clamps with plastic-dipped jaws)

- 6 function mutli tool - Hex keys: 3/4/5/6mm - Flathead and Phillips screwdrivers

- Single 29mm open bore drift for use with 1/2" rods

Our 2437 open bore adapter is used to press 24x37 sealed bearings into bottom bracket cups, and direct fit frames like trek BB90. The adapter is machined with one step at 24mm ID, which fits into the center of the sealed bearing. - Installs: 24x37 bearing - Inner step outer diameter: 23. 8mm - Outer diameter: 36. 8mm - Thru hole diameter: 0. 387" (9. 8mm) - Inner hole sized to fit 1/2" threaded rod - Compatible with BP0006, BP0007 - Machined, red anodized aluminum - Sold individually (2 drifts required for some installations)

This 29mm open bore adapter is used to press 29mm x 42mm (DUB) sealed bearings. The adapter is machined with one step at 29mm OD, which fits into the center of the sealed bearing. For use with Wheels Mfg. bottom bracket press (PRESS-7 , PRESS-7-PRO or PRESS-9-PRO). - Inner step outer diameter: 28.9mm - Outer diameter: 41.8mm - Thru hole diameter: 12.8mm (1/2-inch) - Thickness: 7mm - Machined, red anodized aluminum - Sold individually

Our 6806 open bore adapter is used to press 42x30 sealed bearings. The adapter is machined with one step at 30mm ID, which fits into the center of the sealed bearing. Common bearing size for BB30 frames and bottom brackets. - Installs: 6806 bearing - Inner step outer diameter: 29. 9mm - Outer diameter: 41. 8mm - Thickness: 7mm - Thru hole diameter: 0. 387" (9. 8mm) - Inner hole sized to fit 1/2" threaded rod - Compatible BP0006, BP0007 - Machined, red anodized aluminum - Sold individually (2 drifts required for some installations)

Our GXP-LEFT open bore adapter is used to press 22x37 sealed bearings into SRAM GXP bottom bracket cups and direct fit frames like trek BB90. The adapter is machined with one step at 22mm OD, which fits into the center of the sealed bearing. - Installs: 22x37 (GXP) bearing - Inner step outer diameter: 21. 9mm - Outer diameter: 36. 8mm - Thickness: 7mm - Thru hole diameter: 0. 387" (9. 8mm) - Inner hole sized to fit 1/2" ACME threaded rod - Compatible with BP0006, BP0007 - Machined, red anodized aluminum - Sold individually

Wheels Manufacturing open bore adapters are used to press sealed cartridge bearings into place. The adapters are machined with one step to correspond to the bearing OD, which fits in to the center of the sealed bearing and an outside diameter to accommodate the bearing's outer diameter. Size: [Bearing inner diameter] x [Bearing outer diameter] Note: If only one dimension is given, that is the outer diameter of the adapter, with no inner diameter step

Wheels Manufacturing Over Axle Adapters are used for pressing your most commonly used bearing sizes into place. Each represents an excellent addition to the Press-4 Bearing Press. - Adapters sold individually

• RockShox Dynamic Seal Grease (PTFE) • Recommended for rear shock service

- Evaporates fast and leaves no residue - A "no-scrub" cleaner that cleans to the base and prepares surfaces for application of high-performance lubricants - No water rinsing is required - Clean Streak's No-Rinse, No-Residue formula is perfect for use on disc brake rotors

- Grease for periodic maintenance of suspension/dropper seatposts - Works well on most shocks and forks

- Consumer grade spray cleaner removes dirt and grime - Safe on all parts including carbon

Park's Anti-Seize Compound reduces friction in threaded and press fit connections for easy assembly and disassembly. It's ideal for bottom brackets, pedal threads, headset cups, seatposts, quill stems and much more. This compound also seals and protects parts from corrosion and rust under the most extreme conditions.

A handy tool designed to make installation and removal of bicycle electronic shifting wires and batteries quick and easy. The durable composite body features our iconic three-way wrench shape and prevents scratching of expensive components. Angled ends allow for safe installation and removal of Shimano Di2 E-tube EW-SD300; wires in tight spaces. Universal coin cell tool helps remove and install battery covers on SRAM AXS and other electronic accessories. - Compatible with Shimano Di2 E-tube, EW-SD300 wires (nominally 3 mm OD connector) - Not compatible with Shimano Di2 E-Tube EW-SD50 wires (nominally 5 mm OD connector) — use the Park Tool EWS-1

Park's Bladed Spoke Holder is a must for building and truing wheels that feature bladed spokes. It has 4 different size slots to fit a wide variety of bladed (aero) spokes from .08 to 2mm wide. It holds them safely in place to prevent twisting as you turn the nipple to true and tension the wheel.

Heat-treated alloy tool steel, one inch base fits wrench or bench vise. Thin-wall construction allows use without removal of cones and locknuts. The FR-5 has 12 splines that are approximately 23.4mm across. - Fits Shimano, SRAM, Sunrace, Suntour, Chris King and other cassette lockrings - Fits the SRAM XX1 11-speed cassettes - Also fits Shimano disc brake lockrings - Always use a quick-release skewer to hold the tool in place and snug to cogs when loosening; for solid axles, use the axle nut

Regular lubrication of bicycle chains addresses annoying squeaks and noises, and extends the life of the chain and drivetrain components. Formulated using a proprietary blend of oils, Park Tool CL-1.2 Chain Lube works great in wet or dry conditions. It penetrates, reduces friction, prolongs component life, displaces moisture, and protects parts from rust and corrosion. Compatible with all bicycle chains. Also works great as general-purpose light lubricant for use on bicycle brake and derailleur cables and housing, spoke nipples, and derailleur and brake pivots. - 4 fl. oz. (118 mL) bottle NOTE: Some painted surfaces can be sensitive to oil and grease. Clean off any excess oil or grease immediately. Test first on an inconspicuous area to see if it causes a stain or discoloration.

A handy tool designed to make installation and removal of bicycle electronic shifting wires and batteries quick and easy. - Durable composite body is durable and prevents scratching of expensive components - Angled Shimano Di2 E-TUBE ends allow for both installation and removal in tight spaces - Universal coin cell tool helps remove and install battery covers on SRAM eTap

The MTC-10 features a super strong, composite, multi-position handle, with hardened and plated tools and smooth ergonomic operation. Lightweight, compact, and perfect to carry along. - 3, 4, 5 and 8mm hex wrenches - T25 Torx compatible driver - Combo cross/straight tip screwdriver - Key ring holder - Weight: 60g (2.12 ounces)

Park's Offset Brake Wrench utilizes a unique design that allows it to reach into tight areas that other wrenches cannot. The OBW-3 features a 14mm wrench on one end and the other end fits into a brake's tension springs to rotate the brake around its bolt for proper alignment. The OBW-4 features 10-, 11-, 12-, and 13-mm opening to fit most models of sidepull brakes.

Choose the perfect tool for the job with Park's P-Handled Hex Wrenches. These top-shelf Allen wrenches come with offset handles made from durable nylon in a comfortable, ergonomic design. They are made of chrome vanadium for exceptional durability. The long shafts feature Bondhus heads for accessing hard-to-reach bolts and the short ends are chamfered for extra grip and high-torque applications.

Park Tool is world-renowned for their bicycle industry tools, and their pumps are no exception. Keep yours up to speed and working smoothly with these rebuild kits. - 1096K: Contains one #1081 head as well as one #1075 plunger gasket for older PFP-2 and first generation PFP-4 floor pumps. Also compatible with second-generation PFP-4 floor pumps. - 1096X: Contains one #1096R head, one #1472 fitting, and one #1075 plunger gasket for second generation PFP-4 floor pumps. Also compatible with PFP-2 and first-generation PFP-4 floor pumps. - 1096Z: Contains one #1096R head, one #1472 fitting, and one #1087 plunger gasket for PFP-5 and PFP-7 floor pumps. Also compatible with PFP-3, PFP-6, and PFP-8 floor pumps.

Park's Cone Wrenches are made of durable tool steel and are nice and thin to fit on the small-clearance cones found on hubs and other bearing assemblies. Plus, they work as regular wrenches, too. They feature Park's special Y heads that put more material where it's needed for excellent durability and strength. Most applications require at least 2 cone wrenches. If you have questions please contact us and we can recommend the correct sizes for your needs.

Park's Cone Wrenches are made of durable tool steel and are nice and thin to fit on the small-clearance cones found on hubs and other bearing assemblies. Plus, they work as regular wrenches, too. They feature Park's special Y heads that put more material where it's needed for excellent durability and strength. This 23mm size fits Shimano 15mm through-axle hubs. Some applications require at least 2 cone wrenches. If you have questions please contact us and we can recommend the correct sizes for your needs.

Park's Cone Wrenches are made of durable tool steel and are nice and thin to fit on the small-clearance cones found on hubs and other bearing assemblies. Plus, they work as regular wrenches, too. They feature Park's special Y heads that put more material where it's needed for excellent durability and strength. This 24mm wrench fits Shimano 15mm through-axle front hubs and many suspension-fork top caps. Some applications require at least 2 cone wrenches. If you have questions please contact us and we can recommend the correct sizes for your needs.