Parts & Accessories

Whisky’s tubeless rim tape is designed to make setup as easy as possible. Elasticity allows for smooth, even adherence while translucency lets you see where the tape contacts the rim. Different widths available to fit almost any rim.

Machined aluminum spacers for freehubs. Great for fine tuning freewheel and cassette placement or improving chainline. Also good for bottom bracket spacing with BSA BB cups. - Inner Diameter: 35.0mm - Outer Diameter: 40.7mm - Material: Aluminum - Finish: Polished - Bags of 10

Stan's lightweight aluminum valve stems are half the weight of Stan's standard brass valves. The secure round base is compatible with most tubeless rims and a perfect fit for all Stan's BST rims. A removable valve core makes adding sealant easy, and these babies fit up to 8mm valve hole. Sold as a pair.

Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3

Get rolling again with a replacement 10-speed freehub body for Mavic wheels.

The buyer's choice for wheel builders looking to save weight. The nipples are available with or without DT Pro Lock, a patented liquid inside the nipple thread that makes the connection between the nipple and spoke extremely durable. It pairs perfectly with any wheel, though all-brass nipples are recommended for e-bike use. - Weight: starting at 20g for 64 nipples

Refresh your Bontrager wheels. Genuine replacement parts When it's time to refresh your trusty wheelset, Trek Genuine Replacement Parts have you covered. - Replacement freehub body for Bontrager DC-3248 Hyeperglide hub - Can also be used to upgrade DC-1248 hubs - Requires DC-3248 Axle Kit when installed on DC-1248 hubs - Requires 14mm hex wrench to install/remove - Threaded freehub only compatible with DC-3248 Hyperglide hub platforms

Upgrade or refresh your bike. - Original equipment replacement axle kit for DC-3248 hubs - Can also be used to upgrade DC-1248 hubs when used with DC-3248 freehub - Includes axle and end nuts for DC-1248 and DC-3248 platforms - 11.65mm non-drive side nut for use with DC-1248 hubs - 9.75mm non-drive side nut for use with DC-3248 hubs

Upgrade or refresh your Bontrager wheels. When it's time to refresh your trusty wheelset, Trek genuine replacement parts have you covered. PRODUCT DETAILS - Original equipment replacement freehub for RX-342 hubs - Can also be used to upgrade RX-142 hubs - Requires RX-342 Axle Kit when installed on RX-142 hubs

To be used exclusively with Bontrager Tubeless Ready (TLR) rims. The rim strips you need to upgrade to Tubeless These rim strips are crucial in upgrading your Tubeless Ready (TLR) Bontrager wheels to the next level of dependability and performance. Product details - TLR Rim Strips are the light and easy solution to Bontrager Tubeless conversion - Use only with appropriate Bontrager TLR rim valve - Rim strip replacement is recommended if removed from the wheel - Sold as singles - White strip is recommended for carbon rims - TLR rim valve sold separately

Bontrager Tubeless (TLR) Rim Tape creates an air-tight seal that covers spoke holes in the rim for easy tubeless tire setup and installation. The tape securely bonds to the rim and doesn't leave residue when removed. For use with wheels approved for TLR Tape-based tubeless conversion. - Provides durable, air-tight seal over spoke holes for tubeless conversion - Wrap four wheels with a single layer of tape or two wheels with a double layer - Provides secure adhesion to rim without leaving residue when removed - Thoroughly clean and dry rim bed before applying - For use with rims approved for TLR Tape-based tubeless conversion

Zipp 101 XPLR MOTO Rim Strip And Tubeless Tape Kit (includes rim strip and tubeless tape for 1 wheel).

Includes rim strip and tubeless tape for 1 wheel.

Wheel Conversion Caps for Zipp 77/177 Disc hubs. Converts your Zipp 77 or 177 hubs to nearly any frame standard.

These die-cut borderless decals provide a distinctive look to go with the distinctive sound and aero-advantage of Zipp wheels rolling at 45km an hour. Zipp’s Matte white and Matte black decals also are still available. Each decal kit has seven decals sufficient to cover one wheel and two matching valve-hole decals. Note: Before applying the decals, make sure the rim surface is free of dirt and debris. We recommend a gentle wipe with acetone or rubbing alcohol. Peel the white backing sheet from the decal, orientate, position and gently press the decal onto the rim surface. Starting at one end, remove the surface clear cover slip and then work the decal into the dimples using a 3M squeegee.

- Hub axle, front - Zipp Cognition V2 Disc Brake (axle & wave spring)

- Hub axle, front - Zipp Cognition V2 Rim Brake (axle & wave spring)

- Hub axle end cap set, rear - Zipp Cognition V2 Disc Brake - Rim brake compatible with XDR & 11-speed

- Hub axle end cap set, rear - Zipp Cognition V2 Rim Brake - Quick release

The Wolf Tooth Rear Axle uses a captive steel washer under the head to reduce friction on the dropout face. This protects your expensive frame, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. - Made in Minnesota to aerospace standards

The Wolf Tooth axle uses a captive steel washer under the head to reduce friction on the fork leg. This protects your expensive fork, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. These are also a great replacement option for lost or damaged stock axles. Always apply a small amount of grease to the washer and threads when installing. - Designed and manufactured in Minneapolis, MN USA 7075 T6 Aluminum

Boostinators are hub specific conversions designed to take non-boost hubs and convert them to boost compatibility. Don't toss out that wheelset - Boostinate it.

Boostinator kits allow non-boost wheels to be mounted in Boost spacing frames and forks. While incremental, the benefits of the "Boost" 15x110mm front and 12x148mm rear axle standards are clear: better clearance for fatter tires & rims and reduced dish for stiffer, stronger wheels. The big bummer? Taking full advantage requires not only a new frame and fork, but new wheels as well. In response, we have developed the Boostinator. When paired with compatible 15x100mm or 12x142mm hubs, Boostinator kits allow existing wheels to be mounted in Boost-standard frames and forks. Disc and drivetrain positions are maintained and, thanks to a quick re-dish, spoke bracing angles are improved. Boostinator kits consist of a specially-designed axle end cap and, in the case of rear kits, a precision-machined rotor spacer with a set of six high-strength bolts. In keeping with Boost specifications, the disc and cassette are shifted outboard, allowing brakes and derailleurs to function as designed. Compatibility: - Front boostinators are only an endcap and do not require a rotor spacer. The wheel is re-dished. - Rear boostinators require both a re-dish and rotor spacer. - Rear Boostinator kits are not approved for rotors larger than 183mm. - Hubs spacing is 100mm front and 142 rear, and the Boostinators make them 110 and 148 respectively. - Compatible with 6-bolt FRONT wheels and SOME centerlock models. - Compatible with ONLY 6-bolt REAR wheels (there is no way to space centerlock rotors over 6mm). - NOT recommend (or safe) for non-symmetric lacing like the 2:1 lacing found on some of Industry Nine's wheels. *Note: You will need to re-dish your wheel after installing any Boosinator. Boostinator DR: - The Boostinator DR is compatible with DT-Swiss 12x142mm Star Ratchet (240- and 350-series) rear hubs with 6-bolt (IS) rotor mounts. - Centerlock hubs are not supported. - 180- and 190-series hubs are Centerlock only. - The Boostinator DR is also compatible with some complete wheels from DT Swiss, Roval (Specialized), Giant, Syncros (Scott), and others that use DT's Star Ratchet internals. - Remove the disc side end cap. Bearing size 6802 15x24. - Net weight: 18g Boostinator HR: - The Boostinator HR is compatible with 12x142mm Hope Pro 2 EVO and Pro 4 rear hubs. - Non-EVO Pro 2 hubs are not supported - Net weight: 18g Boostinator 9TR: - Compatible with 142x12 rear Industry Nine Torch hubs. - Not compatible with 2:1 lacing wheels from Industry Nine - Not compatible with Centerlock hubs Tech Specs: - Material: 6061 aluminum - Included: Rear kits come with appropriate-length Class 10.9 bolts, each roughly 40% stronger than more common Class 8.8 hardware.

The Wolf Tooth Rear Axle uses a captive steel washer under the head to reduce friction on the dropout face. This protects your expensive frame, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. - Made in Minnesota to aerospace standards

- Colored rim decal kits to personalize your ride - Decals to fit 2 100w 26-inch rims

- Colored rim decal kits to personalize your ride - Decals to fit two (2) 50w 27.5+ rims

- Colored rim decal kits to personalize your ride - Decals to fit two (2) 70w 26-inch rims

Ultra light bolt on thru axle, with a low profile 6mm head for Whisky forks and some others. See other manufacturers specifications for fitment questions. - Thread Length (mm): 12 - Thread Pitch: 1.5 - MT/CX: 125 x 15mm - MTB+: 135 x 15mm - Fat: 198 x 15mm - RD/CX: 120 x 12mm - Rear: 167 x 12mm

Ultra-light, bolt-on thru-axles, with a low-profile 6mm head for use on Whisky forks and others. They are also available in some common rear frame sizes. See manufacturer's specifications for fitment questions. - Thread Length: 12mm

Wheels Manufacturing Axle Spacers help you dial in your hub spacing to ensure correct fit and side-to-side spacing in the rear triangle without having to alter the wheel's dish. - Spacers come in bags of 20